Butterfly Valves
For corrosive and abrasive media
The economic advantages of reduced maintenance, smooth operation and exceptional service life are proven over and over again. The reliability of Garlock butterfly valves is not only appreciated and well known at our customers but also certified with SIL up to level 3 according to EN 61508. Each valve is in line with ISO 15848-1 and TALuft 2021 standards and can vary in lining, disc and elastomer materials depending on your application. Available linings are virgine PTFE, abrasive PTFE, antistatic PTFE and UHMWPE. Garlock valves set the standard in high quality. To ensure this and guarantee a long reliable lifetime the Garlock quality management system is certified according to ISO 9001 and regulation 2014/68/EU Module H1 (PED). Each valve is extensively tested according to EN 12266 P10, 11 and 12 before leaving our factory.
Butterfly Valves
GAR-SEAL®
GAR-SEAL® valves are used extensively where corrosive, abrasive and toxic media needs to be reliably controlled. They are typically used for accurate control, throttling and shut-off duties in the chemical, petrochemical, chlorine, paper, electro-plating and many other industries. GAR-SEAL butterfly valves offer reduced maintenance requirements and increased operational reliability.
Features & Benefits
-
Provide accurate control
-
Offer reduced maintenance
-
Increase operational reliability
Specifications
Size Capability:
- DN 50 / 2“ bis DN 600 / 24“
Flange Connection:
- EN 1092 PN 10/16 (Design A/B)
- ASME B16.5 class 150 lbs (Design RF/FF)
Face-to-Face Dimensions:
- DIN EN 558-1 GR 20 (DN 350 GR25)
- ISO 5752 Table 5 short
- ASME B16.10 (2“ bis 12“ Table Narrow 14“ to 24“ Table Wide)
- MSS-SP 67 (2“ bis 12“ Table Narrow 14“ to 24“ Table Wide)
- API 609 (2“ bis 12“ Category A Table 2 14“ to 24“ Category B Table 3)
Body Strength:
- DIN/ EN 12516 T2 (DIN 3840)
- Tested within the scope of the inspection body designate by Module H1
Operating Pressure:
- DN 50/2“ bis 300/12“: 16 bar
- Above DN 300/12“: 10 bar (depending on operating temperature)
Testing:
- EN 12266 P10
- EN 12266 P11
- EN 12266 P12 Leak rate A
Bodies:
- Wafer and Lug design with long neck for insulation
Vacuum:
- Up to 1 mbar abs. (depending on size and temperature)
Temperature Range:
-40°C up to 200°C (depending on material)
Head Flange:
- EN ISO 5211
- NF E 29-402
Liners
- PTFE
- Abrasive PTFE
- UHMWPE
SAFETY-SEAL
SAFETY-SEAL valves are used in applications where corrosive, abrasive and toxic media need to be handled and
electrostatic charges must be avoided at the same time.
Features & Benefits
-
Provides accurate control
-
Offers reduced maintenance
-
Increases operational reliability
-
Long life
-
Reduces maintenance efforts
Specifications
Dimensions:
- DN 50 / 2“ bis DN 600 / 24“
Flange Connection:
- EN 1092 PN 10/16 (Design A/B)
- ASME B16.5 class 150 lbs (Design RF/FF)
Face-to-Face Dimensions:
- DIN EN 558-1 GR 20 (DN 350 GR25)
- ISO 5752 Table 5 short
- ASME B16.10 (2“ bis 12“ Table Narrow 14“ to 24“ Table Wide)
- MSS-SP 67 (2“ bis 12“ Table Narrow 14“ to 24“ Table Wide)
- API 609 (2“ bis 12“ Category A Table 2 14“ to 24“ Category B Table 3)
Body Strength:
- DIN/EN 12516 T2 (DIN 3840)
- Tested within the scope of the inspection body designate by Module H1
Operating Pressure:
- DN 50/2“ to 300/12“: 16 bar
- Above DN 300/12“: 10 bar (depending on operating temperature)
Testing:
- EN 12266 P10
- EN 12266 P11
- EN 12266 P12 Leak rate A
Bodies:
- Water and Lug design with long neck for insulation
Vacuum:
- Up to 1 mbar abs. (depending on size and temperature)
Temperature Range:
40 °C up to +200 °C, depending on material
Head Flange:
- EN ISO 5211
- NF E 29-402
Liner:
- Antistatic PTFE
MOBILE-SEAL
MOBILE-SEAL valves are used on road tanker vehicles, railway wagons, silos and other transportation and
storage containers where high chemical resistance, reliability and special safety requirements are essential.
Features & Benefits
-
Chemical resistance
-
EN 14432 approved
Specifications
Dimensions:
- DN 50 / 2“ up to DN 100 / 4“ DIN 28459
- DN 50 / 2“ up to DN 150 / 6“ EN 1092
Flange Connection:
- EN 1092 PN 10/16 (Design A/B)
- ASME B16.5 class 150 lbs (Design RF/FF)
- DIN 28459 PN10
Face-to-Face Dimensions:
- DIN EN 558-1 GR 20
- ISO 5752 Table 5 short
- ASME B16.10 (2“ to 4“ Table Narrow)
- MSS-SP 67 (2“ to 4“ Table Narrow)
- API 609 (2“ to 4“ Category A Table 2)
Body Strength:
- DIN/EN 12516 T2 (DIN 3840)
- Tested within the scope of the inspection body designate by Module H1
Operating Pressure:
- DN 50/2“ – 100/4“: 10 bar (depending on operating temperature)
Testing:
- EN 12266 P10
- EN 12266 P11
- EN 12266 P12 Leck rate A
Bodies:
- Water and Lug design with long neck for insulation
Vacuum:
- Up to 1 mbar abs.
Temperature Range:
- –40 °C up to +200 °C (depending on material)
Head Flange:
- EN ISO 5211
- NF E 29-402
Liner:
- PTFE
- Antistatic PTFE
- Abrasive PTFE
- UHMWPE
Certificates:
- EN 14432
- TÜ-AGG 044-84
Downloads
- Certificate TA-Luft ISO 15848-1 (German language)
FOOD SAFE – EC1935/2004, EC 10/2011 conformity
Falkenweg 1
41468 Neuss
Germany
+49 2131 349-0
garlockgmbh @ garlock.com
© 2024 Garlock GmbH, Germany
Garlock Global Website
www.garlock.com
Career Site Europe
https://www.garlock-karriere.de/en